A wireless mic system is two boxes. A transmitter on the speaker's belt, with a lav mic plugged into it, turns the voice into a radio signal, and a receiver on the camera or sound recorder turns it back into audio. It means nobody's tied to the camera by a cable. It also means you're relying on a radio link, which is why any decent crew records a backup and listens on headphones the entire time.
Wireless kit has got smaller and cheaper over the last few years, to the point where plenty of people filming on their own now own a set. That's good news. The radio side still behaves like radio, though, and knowing roughly how it works is the difference between a clean interview and forty minutes of something you can't use.
How does a wireless microphone work?
The transmitter is a small pack, usually clipped to a belt or the back of a waistband, with the lav cable running up under the shirt to the chest. Some newer compact systems build the microphone into the transmitter itself, so the whole thing clips straight onto clothing. The transmitter sends the audio out on a radio frequency.
The receiver sits on the camera or feeds a separate sound recorder. It's tuned to the same frequency as the transmitter, picks up the signal and passes the audio into the recording. One receiver can often take two transmitters, which is handy for two-person interviews.
There are two broad families. Analogue systems have been the standard for decades and usually work in the UHF range. Digital systems convert the audio to data before sending it, which tends to sound cleaner, at the cost of a very small delay. Many compact digital systems work at 2.4GHz, the same band used by wifi and Bluetooth, which matters for the next part.
What frequencies do wireless mics use in the UK?
Radio spectrum in the UK is managed by Ofcom, and wireless mics have to stay inside the bands they're allowed to use. According to Ofcom's guidance on wireless microphones, the ranges 173.8 to 175 MHz, 863 to 865 MHz and 2400 to 2483.5 MHz can be used without a licence, but they're shared with other low-power equipment and so are open to interference. Other UHF frequencies need a licence, and coordinated licences for a specific site give the best protection.
In plain terms, the licence-free bands are busy. Wifi routers, phones, wireless speakers and other people's mics are all in there with you. Kit bought abroad may also be set to frequencies that aren't allowed here, so check it's sold for UK use. If a crew is working somewhere with heavy radio traffic, like a big event or a city centre office, licensed frequencies are part of how they keep the link clean.
What causes interference and dropouts?
A dropout is a moment where the receiver loses the signal and the audio cuts, crackles or goes digital and glitchy. The usual causes are worth knowing because most of them are easy to avoid:
- Other devices on the same frequency. Most receivers can scan for a clear channel. Do it at the location, not at home.
- The human body. We're mostly water, and water soaks up radio signal. A transmitter on someone's back with the receiver in front of them is working through a person.
- Distance and obstacles. Walls, metal shelving, cars and fridges all weaken the signal. Keep a clear line between transmitter and receiver where you can.
- Too many systems at once. Several transmitters close together can interfere with each other, especially in the narrow licence-free bands.
- Batteries. As they run down, range shrinks and dropouts start. Fresh or fully charged batteries at the start of every interview, not halfway through.
Why record a backup?
Because a radio link can fail and you won't always know straight away. Plenty of current transmitters can record the audio internally as well as sending it, which means even if the signal drops, there's a clean copy sitting on the pack. Others use a separate small recorder on the speaker. Either way, the backup gets lined up with the main recording in the edit, using timecode or by matching the sound waves.
Some crews also record a second safety track on the main recorder, the same voice set a little quieter, so if someone suddenly shouts or laughs, there's a version that didn't clip. Newer recorders that work in 32-bit float handle loud peaks far better, but the backup copy is still worth having. I'd treat any interview you can't easily reshoot, and that's most of them, as one that needs two copies of the voice.
A wireless link is a radio, and radios drop out. Plan for the moment it does.
Why does someone need to wear headphones the whole time?
Because the meters only tell you how loud something is. They don't tell you what it is. A recording can sit at a perfect level and still be full of shirt rustle, a fridge hum, a buzz from a nearby cable or a dropout that lasted half a second. You only catch those by listening, and you only fix them on the day if you hear them on the day.
Whoever's monitoring should be listening to what's actually being recorded, through closed-back headphones that block out the room. The things they're listening for:
- Rustle and taps from clothing or hands
- Crackle, cuts or glitches that mean the signal's struggling
- Background noise that's crept up, like traffic, aircon or a phone on silent buzzing on the table
- A voice that's gone muffled because the mic has slipped under a fold of shirt
When they hear something, they stop the interview at a natural pause and fix it. It's mildly awkward for a second. It's a lot less awkward than discovering in the edit that the best story of the day has a dropout through the middle of it.
La FromagerieOur La Fromagerie film was shot in shops that were open and trading, around customers, in cheese rooms that are cold and dark. Busy locations like that are where sound needs the most attention: tills, chatter, fridges and people walking between the camera and whoever's talking.
Is wireless always better than a cable?
No. For a sit-down interview where nobody's moving, a wired mic is the most reliable thing you can use, because there's no radio to go wrong. Wireless earns its place when people are walking, working or moving around a space, when the camera needs to be some distance away, or when a cable across the floor would be a trip hazard or end up in shot.
For a brand documentary, where the good material often comes from people doing their actual work rather than sitting in a chair, wireless is usually part of the kit. It just needs the backup and the headphones to go with it. If you're weighing up which mic to put on someone in the first place, start with lav mics explained, and if you want the bigger picture of what goes into planning a shoot, our free guide covers what happens before the camera comes out.



